After filling and priming the coil with my favorite juice (Thug Juice – 50/50 at 3mg), I set the wattage to a pretty low 20W to allow the coil to slowly bed in. After a few draws with very minimal vapor and flavor, I increased the wattage to 25W. Unscrew the Cerberus tank from the mod. Ensure your tank is empty of e-liquid before you try to disassemble the tank, otherwise you’ll have e-liquid spilling out. Unfortunately, the user manual doesn’t really tell you much about the different settings and what they do. To give a little insight to what the different options mean, we’ve included a brief description below. Power Mode

Also, again depending on your vape mode setting, while scrolling through the settings, you have access to the following: Battery performance is always subjective and depends on the type of batteries you use, the power you vape at and your vaping style. Because I usually vape at low(ish) watts, I opted to use my Sony VTC5A batteries, having a CDR value of 25A with a 2500mAh capacity. The flavor sadly was not very pronounced and I was getting that new coil taste. It took a good tankful of e-liquid before that taste went and the flavor came through really crisp.By pressing the fire button, this will scroll through the top level menus highlighting the following parameters. When you’re in the highlighted parameter, you can then use the +/- buttons to alter the individual settings. This function will allow you to specify different wattages that can be applied to your coil over a vape cycle to fully customize your vaping experience. There are 6 variable wattage settings, each adjustable from 5W to 200W with each setting being adjustable over a time range of 0.5 seconds to 1.2 seconds. The overall height of the tank, including the low profile 810 drip tip and excluding the 510 threaded connector is 35mm. One point worth mentioning, the 510 threaded connector does have a pretty decent protruding center pin (always handy for those hybrid mods).

While using the supplied 0.2 ohm coil, I had no leaks or dry hits and have been using the coil for a week now with no loss of flavor. I was impressed with the flavor and vapor produced from this coil, definitely a thumbs up from me. Temperature Control The X keeps its dual 18650 battery compartment and some small styling details compared to the legend, but that's about it. The screen has had a huge update, with a crystal clear read out of your power, ohm and battery life. The AS chip set has been upgraded to get more battery life and an even faster ramp up time as well as the same TC, Bypass, Volt and Watt options you would expect to find on a modern device. The Aegis X 200W mod is powered by dual 18650 batteries. Always ensure you only use ‘matched pairs’. Further understanding on married/matched batteries can be found in our Pairing Your Vape Batteries guide.They both are durable, and they have many of the same power modes. The most significant differences are that the Aegis X is slightly more responsive because it has an improved chip and a larger screen. Both are good buys, but get the Aegix X to enjoy the latest updates and features from GeekVape. GeekVape Aegis X vs. Voopoo Drag 2

Two coils are supplied with the Aegis X 200W kit but unfortunately both are the same type, the Mesh X1 KA1 0.2 ohm coil. Geekvape specify the wattage for this coil is between 30W–90W, but best at 60W-80W. Interestingly, the Vaporesso GT CCELL, GT mesh and the Smok Baby coils will also fit this tank. Geekvape Aegis X 200W Mod | Functionality To get to this menu, press the fire button 3 times, then straight after, press and hold down the +/- buttons for 3 seconds. Use the +/- buttons to scroll through the different options. Once an option is highlighted, press the fire button to get you into that screen menu. Increasing the wattage to 40W certainly produced a harder hit improving the flavor and vapor no end.Firing the Aegis X is carried out by a fairly large bevelled button on the front above the two smaller +/- bevelled buttons. The response and feel of the buttons is very positive with no button rattle at all. The temperature range for this Geekvape is 200 to 600 degrees Fahrenheit. There are several output modes: powerful, standard, and soft modes. The 2.4 inch OLED color screen is one of the best in the industry, looking more like the screen of a smartphone than a vape. As expected, there are various fire modes, variable power (5w – 200w) Temp Control (100c- 315c) and Bypass mode. All the expected safety features are there too, short circuit, battery overvoltage and so on. Cerberus Tank